The Fundamentals of Plumbing Skills When Installing a Bathtub
The Fundamentals of Plumbing Skills When Installing a Bathtub
Blog Article
Are you currently searching for answers concerning Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is readily available, the task can relocate speedily; if you have to open a wall to remove the old tub and place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. See to it you have actually qualified on your own for the task and fit trying it. As opposed to employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Opportunities are you might need an expert plumber to make tube connections.
This article will help you install a new bath tub in your bathroom if you have currently acquired a new bathtub as well as don't need to alter the setup of your previous water system pipelines.
Your tools as well as product checklist ought to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be rather troublesome due to the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in place between the faucet as well as the sink. Secure the tap in position with the supplier supplied backnut. Once the faucet is securely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type should be connected to the faucet ends initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the tub until the level reads level.
To mount taps, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply and also examine all joints as well as new pipework for leaks and tighten them if essential. Load the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and securing around the tub needs to wait until the bath tub has been utilized at the very least once as this will certainly settle it right into its last placement.
Planning for the Installation
To start with, the supporting framework supplied with the bathroom must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
Fit the versatile faucet adapters to the bottom of the two faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to break a rigid seal, triggering the water to pass through the wall surface between the bathroom as well as the tiling, leading to issues with wetness and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and also can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill the tub with water prior to securing, to permit the motion experienced when the tub is in use. The sealer can split relatively early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog posting on Tools You Need to Install a New Bathtub when doing a search on the internet. Please take a moment to distribute this write-up if you enjoyed it. Thanks a bunch for your time. Please come by our website back soon.
Free Quote Report this page